sustitucion del motor

TALLE
remote controlled
SUSTITUCION DEL MOTOR
board replacement
Top Vision Group – www.topvisiongroup.com
Herramientas necesarias:
-
Llave hexagonal de 2,5 mm
Destornillador PH1
Destornillador 5,5 mm
1. Retire la columna del soporte
inferior
2. Retire los cables
3. Afloje los tornillos del soporte
superior y quite la columna
4. Afloje los tornillos de la tapa en
la parte superior de la columna.
Retire la tapa
5. Deslice hacia arriba el riel de los
soportes de las gafas.
Retire la parte de plástico
6. Afloje los tornillos de la parte
inferior trasera de la columna. Gire
una vuelta el tornillo nº1 y retire el
tornillo nº2 completamente
7. Retire con cuidado el motor
8. Coloque la parte redonda del
muelle exactamente debajo del
agujero
Top Vision Group – www.topvisiongroup.com
9. Suelte la parte de plástico blanco
en el agujero, en la parte redonda
del muelle
10. Vuelva a colocar las tiras
dorsales.
Compruebe que los ganchos se
cierran después de haberlos
abierto manualemente. Si no se
abren repita desde el paso 10.
11. Vuelva a colocar la unidad de
motor. Coloque la nueva unidad de
motor en la columna.
Apretado de los tornillos : Gire el
tornillo nº1 una vuelta y apriete el
tornillo nº 2 pero no muy fuerte
13. Coloque de nuevo la columna
en los soportes y ajuste los
tornillos pero no muy fuerte
La columna está lista para volver a
usar
12. Coloque de nuevo la tapa y
apriete los tornillos
Top Vision Group – www.topvisiongroup.com
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical unit, basic precautions should always be followed, including the following:
Read all instructions before using the Secure Display System DANGER - To reduce the risk of
electric shock:
1.
Always unplug this unit from the electrical outlet before cleaning.
2.
The base of the SECURE DISPLAY SYSTEM contains electronic components. Do not open the base without a
qualified electrician or an official Top Vision dealer.
WARNING - To reduce the risk of burns, fi re, electric shock, or injury to persons:
1.
Unplug from outlet before reassembling parts.
2.
Close supervision is necessary when this unit is used by, or near children, invalids, or disabled persons.
3.
Use this unit only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer.
4.
Never operate this unit if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the SECURE DISPLAY SYSTEM to a service centre for examination and repair.
5.
Keep the cord away from heated surfaces.
6.
Never drop or insert any object into any opening.
7.
Do not use outdoors / for indoor use only!
8.
Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9.
“WARNING: Risk of Electric Shock - Connect this unit to a properly grounded outlet only. See Grounding Instructions.”
SAVE THESE INSTRUCTIONS !
MAINTENANCE INSTRUCTIONS
Instructions for cleaning and user maintenance operations:
1.
The exterior of a SECURE DISPLAY SYSTEM may only be cleaned with a non-static brush.
2.
The SECURE DISPLAY SYSTEM has no user serviceable parts. All malfunctional or
damaged components are to be replaced by a service representative duly authorized by Top Vision
Group BV or an official Top Vision dealer.
INTENDED USE
1.
The indented use of the Secure Display System is to display eyewear frames and
sunglasses.
2.
This product is for commercial use only.
Top Vision Group – www.topvisiongroup.com
Top Vision Group – www.topvisiongroup.com