Onyx Solar ponencia en PV World Forum: Info

Onyx Solar ponencia en PV World Forum: Info

H10 PATENT GLAZING: Building Integrated Photovoltaic
Glazing
GENERAL
Cross-reference
General: read with A90 General technical requirements.
Additional: read V90 Electrical Installation.
PRODUCTS
Building Integrated Photovoltaic Glazing
Detailed design of Building Integrated Photovoltaic Glazing: complete and
submit before commencement of fabrication.
Related works: coordinate with supporting structure, electrical installer and
interfaces in detailed design.
Pane/infill materials: PV external glazing.
General: must have adequate resistance to thermal stress generated by
orientation, shading, solar control and construction.
Glass: to BS 952-1 and relevant parts of:
•
•
•
•
•
•
•
•
•
•
BS EN 572 for basic soda lime silicate glass.
BS EN 1096 for coated glass.
BS EN 1863 for heat strengthened soda lime silicate glass.
BS EN 12150 for thermally toughened soda lime silicate glass.
BS EN 13024 for thermally toughened borosilicate glass.
BS EN ISO 12543 for laminated glass.
BS EN 14179 for heat soaked toughened glass.
BS EN1991-1 (Eurocode) for the calculation of dead & live loads.
Safety glass to be tested in accordance with BS EN 12600.
All safety glass to be marked or suitably labelled in accordance with
internationally recognised standards, strictly in accordance with BS
62662 and BS EN 12600.
SPAIN (Ávila)
C/ Río Cea 1, 46 • 05004
Phone: +34 920 21 00 50
[email protected] • www.onyxsolar.es
UNITED STATES (New York)
1123 Broadway, Suite 908 • NY 10010
Phone: +1 917 261 4783
[email protected] • www.onyxsolar.com
© Copyright Onyx Solar Energy S.L. – All Rights Reserved - Todos los derechos reservados
•
Marks, safety logos or similar to be universally and uniformly located
at a consistent corner, and indicated on the drawings. The effect of
the present WARRANTY will commence on the day of the initial.
Pane dimensions: within ± 2 mm of nominal size.
Quality: clean and free from obvious scratches, bubbles, cracks, rippling,
dimples and other defects.
Performance of BIPV units: the PV module electrical ratings are measured in
Standard Test Conditions (STC), which are: 1000 W/m2 irradiance at an Air
Mass of 1.5 spectrum and cell temperature at 25ºC. These PV modules
deliver the electrical characteristics within +/-5 % of the indicated values
shown in Table 1 (vide infra).
Manufacturing: following standards IEC 616146 and IEC IEC61646 Thin-film
terrestrial photovoltaic (PV) modules – Design qualification and type
approval IEC61730 Photovoltaic (PV) module safety qualification.
Edges: generally undamaged. Shells and chips not more than 2 mm deep
and extending not more than 5 mm across surface are acceptable if
ground out.
Insulating glass units:
•
•
•
Standard: To BS 5713 and Kitemark certified or to BS EN 1279.
Perimeter seals: Resistant to UV light degradation on exposed edges.
Edge seal strength: To BS EN 1279-4.
SPAIN (Ávila)
C/ Río Cea 1, 46 • 05004
Phone: +34 920 21 00 50
[email protected] • www.onyxsolar.es
UNITED STATES (New York)
1123 Broadway, Suite 908 • NY 10010
Phone: +1 917 261 4783
[email protected] • www.onyxsolar.com
© Copyright Onyx Solar Energy S.L. – All Rights Reserved - Todos los derechos reservados
Materials:
See-thru S-Clear 10% BIPV glazing based in amorphous silicon active layer
Manufacturer: Onyx Solar Energy
Quantity: XXXX units
Reference: 636BN-12451242-10-1
Table 1: PV Module Electrical Characteristics at STC
•
•
•
•
•
•
•
•
•
•
•
•
•
Length: 1245 mm
Width: 1242 mm
Thickness: 18,24 mm
Weight: 58,90 kg
Type of PV Cell: a-Si Thin Film Solar Cells
Transparency degree: S-Clear 10%
Nominal peak power: 73.32 Wp
Open-circuit voltage: 94 Voc(V)
Short-circuit current: 1,15 Isc (A)
Voltage at nominal power: 70,50 Vmpp(V)
Current at nominal power: 1,04 Impp(A)
Power tolerance not to exceed: ± 5%
Maximum system voltage: 1000 Vsys (V)
Glass configuration as triple laminated PV glass:
•
•
•
•
First layer: 6mm low-iron tempered glass.
Second layer: 3,2mm float glass PV a-Si active See-thru 10%.
Third layer: 6mm clear tempered glass.
Encapsulant: polyvinyl butyral interlayer (PVB) and encapsulant
thickness: 2 foils per interlayer of 1,52mm in PVB layers.
IGU unit:
•
•
Gas spacer: 8mm Argon.
Inner glass: double laminated 4mm float glass low-e/4mm float
glass.
SPAIN (Ávila)
C/ Río Cea 1, 46 • 05004
Phone: +34 920 21 00 50
[email protected] • www.onyxsolar.es
UNITED STATES (New York)
1123 Broadway, Suite 908 • NY 10010
Phone: +1 917 261 4783
[email protected] • www.onyxsolar.com
© Copyright Onyx Solar Energy S.L. – All Rights Reserved - Todos los derechos reservados